> init Running power-on diagnostics... System Maintenance Menu 1) Start System 2) Install System Software 3) Run Diagnostics 4) Recover System 5) Enter Command Monitor Option? 2 Installing System Software... Press to return to the menu. 1) Remote Tape 2) Remote Directory 3)[Local CD-ROM] X) Local Tape *a) Local SCSI CD-ROM drive 4 Enter 1-4 to select source type, a to select the source, to quit, or to start: Insert the installation CD-ROM, then press : ARCLoader version 0.4 (c) 2004-5 Stanislaw Skowronek Loading configuration for '/unix'... Detecting system parameters... Loading pci(0)scsi(0)cdrom(4)partition(8)/ip32r5k... Reading 5341318 bytes... OK. Entering kernel. Linux version 2.6.12-rc5-mipscvs-20050606-ip32r5k (root@khazad-dum) (gcc version 3.4.3-20050110 (Gentoo Linux 3.4.3.20050110-r2, ssp-3. 4.3.20050110-0, pie-8.7.7)) #3 Wed Jun 8 00:39:13 EDT 2005 ARCH: SGI-IP32 PROMLIB: ARC firmware Version 1 Revision 10 CRIME id a rev 1 at 0x0000000014000000 CRIME MC: bank 0 base 0x0000000000000000 size 32MiB CRIME MC: bank 1 base 0x0000000002000000 size 32MiB CRIME MC: bank 2 base 0x0000000004000000 size 32MiB CRIME MC: bank 3 base 0x0000000006000000 size 32MiB CPU revision is: 00002321 FPU revision is: 00002310 Determined physical RAM map: memory: 0000000008000000 @ 0000000000000000 (usable) Initial ramdisk at: 0xffffffff8045c000 (294912 bytes) Built 1 zonelists Kernel command line: console=ttyS0,9600 root=/dev/ram0 discord Primary instruction cache 32kB, physically tagged, 2-way, linesize 32 bytes. Primary data cache 32kB, 2-way, linesize 32 bytes. R5000 SCACHE size 512kB, linesize 32 bytes. Synthesized TLB refill handler (31 instructions). Synthesized TLB load handler fastpath (45 instructions). Synthesized TLB store handler fastpath (45 instructions). Synthesized TLB modify handler fastpath (44 instructions). PID hash table entries: 1024 (order: 10, 32768 bytes) Calibrating system timer... 180 MHz CPU detected Using 90.014 MHz high precision timer. Console: colour dummy device 80x25 CRIME memory error at 0x3fffffe0 ST 0x0400a828 Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Memory: 123136k/131072k available (3769k kernel code, 7688k reserved, 975k data, 472k init, 0k highmem) Mount-cache hash table entries: 256 Checking for 'wait' instruction... available. Checking for the multiply/shift bug... no. Checking for the daddi bug... no. Checking for the daddiu bug... no. checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 288k freed NET: Registered protocol family 16 MACE PCI rev 1 SCSI subsystem initialized usbcore: registered new driver hub MACEPCI: Master abort at 0x00004000 (C) EFS: 1.0a - http://aeschi.ch.eu.org/efs/ JFS: nTxBlock = 966, nTxLock = 7729 SGI XFS with ACLs, large block/inode numbers, no debug enabled gbefb: allocating memory Console: switching to colour frame buffer device 80x30 fb0: SGI GBE rev 1 @ 0x16000000 using 2048kB memory rtc: SRM (post-2000) epoch (2000) detected Real Time Clock Driver v1.12a Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 53) is a 16550A ttyS1 at MMIO 0x0 (irq = 59) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 1 RAM disks of 9216K size 1024 blocksize loop: loaded (max 8 devices) eth0: SGI MACE Ethernet rev. 1 PCI: Enabling device 0000:00:01.0 (0046 -> 0047) ahc_pci:0:1:0: Using left over BIOS settings PCI: Enabling device 0000:00:02.0 (0046 -> 0047) ahc_pci:0:2:0: Using left over BIOS settings scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 aic7880: Wide Channel A, SCSI Id=0, 16/253 SCBs Vendor: SGI Model: IBM DCAS-32160W Rev: S62A Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:1:0: Tagged Queuing enabled. Depth 48 target0:0:1: Beginning Domain Validation WIDTH IS 1 (scsi0:A:1): 6.600MB/s transfers (16bit) target0:0:1: Domain Validation skipping write tests (scsi0:A:1): 20.000MB/s transfers (10.000MHz, offset 8, 16bit) target0:0:1: Ending Domain Validation Vendor: SGI Model: IBM DCAS-32160W Rev: S62A Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:2:0: Tagged Queuing enabled. Depth 48 target0:0:2: Beginning Domain Validation WIDTH IS 1 (scsi0:A:2): 6.600MB/s transfers (16bit) target0:0:2: Domain Validation skipping write tests (scsi0:A:2): 20.000MB/s transfers (10.000MHz, offset 8, 16bit) target0:0:2: Ending Domain Validation Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 0167 Type: CD-ROM ANSI SCSI revision: 02 target0:0:4: Beginning Domain Validation target0:0:4: Domain Validation skipping write tests (scsi0:A:4): 10.000MB/s transfers (10.000MHz, offset 8) target0:0:4: Ending Domain Validation scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 aic7880: Wide Channel A, SCSI Id=0, 16/253 SCBs st: Version 20050312, fixed bufsize 32768, s/g segs 256 SCSI device sda: 4197405 512-byte hdwr sectors (2149 MB) SCSI device sda: drive cache: write through SCSI device sda: 4197405 512-byte hdwr sectors (2149 MB) SCSI device sda: drive cache: write through sda: sda1 sda2 sda3 sda9 sda11 Attached scsi disk sda at scsi0, channel 0, id 1, lun 0 SCSI device sdb: 4197405 512-byte hdwr sectors (2149 MB) SCSI device sdb: drive cache: write through SCSI device sdb: 4197405 512-byte hdwr sectors (2149 MB) SCSI device sdb: drive cache: write through sdb: sdb1 sdb2 sdb3 sdb9 sdb11 Attached scsi disk sdb at scsi0, channel 0, id 2, lun 0 sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.20 Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0 Attached scsi generic sg1 at scsi0, channel 0, id 2, lun 0, type 0 Attached scsi generic sg2 at scsi0, channel 0, id 4, lun 0, type 5 usbmon: debugs is not available USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid10 personality registered as nr 9 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 308.000 MB/sec 8regs_prefetch: 308.000 MB/sec 32regs : 308.000 MB/sec 32regs_prefetch: 308.000 MB/sec raid5: using function: 32regs_prefetch (308.000 MB/sec) raid6: int64x1 50 MB/s raid6: int64x2 70 MB/s raid6: int64x4 78 MB/s raid6: int64x8 58 MB/s raid6: using algorithm int64x4 (78 MB/s) md: raid6 personality registered as nr 8 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 472k freed init started: BusyBox v1.00 (2005.06.02-01:26+0000) multi-call binary Starting pid 23, console /dev/ttyS0: '/linuxrc' mount: block device /dev/loop0 is write-protected, mounting read-only atkbd.c: keyboard reset failed on mace/serio0 atkbd.c: keyboard reset failed on mace/serio1 Gentoo Linux; http://www.gentoo.org/ Copyright 2001-2005 Gentoo Foundation; Distributed under the GPL Gentoo/MIPS LiveCD RC4 for SGI O2 Systems Built on Prickle-Prickle, the 13rd day of Confusion in the YOLD 3171. * To configure networking, do the following: * For Static IP: * /bin/net-setup [telnet] * For Dynamic IP: * /bin/net-setup dhcp [telnet] * If you would like a telnetd daemon loaded as well, pass "telnet" * As the final argument to /bin/net-setup. BusyBox v1.00 (2005.05.30-06:21+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. / #