Linux version 2.4.21 (embedix@embedix) (gcc version 3.0.4) #48 2004年 11月 19日 金曜日 10:46:05 JST I-O DATA DEVICE, INC. landisk3 support. On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: ro mem=64M root=/dev/hda1 console=ttySC1,9600 CPU clock: 266.80MHz Bus clock: 133.40MHz Module clock: 33.35MHz Interval = 5207 Calibrating delay loop... 266.24 BogoMIPS Memory: 62580k/65536k available (1689k kernel code, 2956k reserved, 271k data, 60k init) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) CPU: SH7751R POSIX conformance testing by UNIFIX PCI: Using configuration type 1 SH7751R PCI: Finished initialization of the PCI controller Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Allocate Area5/6 success. Julian Shutdown button driver initialized Starting kswapd Journalled Block Device driver loaded Installing knfsd (copyright (C) 1996 okir@monad.swb.de). pty: 256 Unix98 ptys configured SuperH SCI(F) driver initialized ttySC0 at 0xffe00000 is a SCI ttySC1 at 0xffe80000 is a SCIF Real Time Clock Driver v1.10e RAMDISK driver initialized: 16 RAM disks of 1024K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AEC6880R: IDE controller at PCI slot 00:01.0 PCI: Enabling device Artop Electronic Corp ATP865 (0005 -> 0007) AEC6880R: chipset revision 7 AEC6880R: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AEC6880R: ROM enabled at 0x01010000 ide0: BM-DMA at 0x4420-0x4427, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x4428-0x442f, BIOS settings: hdc:pio, hdd:pio hda: WDC WD800BB-00BSA0, ATA DISK drive blk: queue 8c21fc40, I/O limit 4095Mb (mask 0xffffffff) ide0 at 0x4400-0x4407,0x440a on irq 6 hda: attached ide-disk driver. hda: host protected area => 1 hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(100) ide-floppy driver 0.99.newide Partition check: hda: hda1 hda2 hda3 ide-floppy driver 0.99.newide SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 197.600 MB/sec 32regs : 284.800 MB/sec raid5: using function: 32regs (284.800 MB/sec) md: multipath personality registered as nr 7 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. [events: 00000004] md: autorun ... md: considering hda3 ... md: adding hda3 ... md: created md0 md: bind md: running: md: hda3's event counter: 00000004 md: RAID level 1 does not need chunksize! Continuing anyway. md0: max total readahead window set to 124k md0: 1 data-disks, max readahead per data-disk: 124k raid1: device hda3 operational as mirror 0 raid1: md0, not all disks are operational -- trying to recover array raid1: raid set md0 active with 1 out of 2 mirrors md: updating md0 RAID superblock on device md: hda3 [events: 00000005]<6>(write) hda3's sb offset: 76024768 md: recovery thread got woken up ... md0: no spare disk to reconstruct array! -- continuing in degraded mode md: recovery thread finished ... md: ... autorun DONE. LVM version 1.0.5+(22/07/2002) NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 8192) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: AppleTalk 0.18a for Linux NET4.0 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 60k freed Adding Swap: 125488k swap-space (priority -1) EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal 8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002) PCI: Enabling device Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (0000 -> 0003) eth0: RTL-8139C+ at 0xfd000000, 00:a0:b0:70:c2:69, IRQ 5 eth0: PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32 PCI: Setting latency timer of device Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ to 64 usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Enabling device NEC Corporation USB (0000 -> 0002) PCI: Setting latency timer of device NEC Corporation USB to 64 usb-ohci.c: USB OHCI at membase 0xfd001000, IRQ 7 usb-ohci.c: usb-00:02.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected PCI: Enabling device NEC Corporation USB (#2) (0000 -> 0002) PCI: Setting latency timer of device NEC Corporation USB (#2) to 64 usb-ohci.c: USB OHCI at membase 0xfd002000, IRQ 8 usb-ohci.c: usb-00:02.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Enabling device NEC Corporation USB 2.0 (0000 -> 0002) ehci-hcd 00:02.2: NEC Corporation USB 2.0 ehci-hcd 00:02.2: irq 5, pci mem fd000100 usb.c: new USB bus registered, assigned bus number 3 PCI: 00:02.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:02.2 PCI cache line size corrected to 32. ehci-hcd 00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22 hub.c: USB hub found hub.c: 5 ports detected Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. usb.c: registered new driver usblp printer.c: v0.11: USB Printer Device Class driver kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 GIO driver initialized. Reset switch driver initialized. Dip switch driver initialized. LED control driver initialized. NFS: NFSv3 not supported. nfs warning: mount version older than kernel NFS: mount program didn't pass remote address! NFS: readdir reply truncated! kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal EXT3-fs: mounted filesystem with ordered data mode.