>> init System Maintenance Menu 1) Start System 2) Install System Software 3) Run Diagnostics 4) Recover System 5) Enter Command Monitor Option? 2 Installing System Software... Press to return to the menu. 1) Remote Directory 2)[Local CD-ROM] *a) Local SCSI CD-ROM drive 7 on controller 1 Enter 1-2 to select source type, a to select the source, to quit, or to start: Insert the installation CD-ROM, then press : ARCLoader version 0.4 (c) 2004-5 Stanislaw Skowronek Loading configuration for '/unix'... Detecting system parameters... Loading scsi(1)cdrom(7)partition(8)/ip28r10k... Reading 5165189 bytes... OK. Entering kernel. Linux version 2.6.12-rc5-mipscvs-20050606-ip28r10k (root@khazad-dum) (gcc version 3.4.3-20050110 (Gentoo Linux 3.4.3.20050110-r2, ssp-3.4.3.20050110-0, pie-8.7.7)) #3 Wed Jun 8 00:37:22 EDT 2005 ARCH: SGI-IP28 PROMLIB: ARC firmware Version 64 Revision 0 CPU revision is: 00000925 FPU revision is: 00000900 Silicon Graphics Indigo2 R10k (IP28) support: (c) 2004 peter fuerst. MC: SGI memory controller Revision 5 MC: Boardrev. 1, Chiprev. 0 MC: Probing memory configuration: bank0: 128M @ 20000000 bank1: 128M @ 28000000 bank2: 64M @ 30000000 Determined physical RAM map: memory: 0000000014000000 @ 0000000020000000 (usable) Initial ramdisk at: 0xa800000020473000 (294912 bytes) Built 1 zonelists Kernel command line: console=ttyS0,9600 root=/dev/ram0 discord Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes. Primary data cache 32kB, 2-way, linesize 32 bytes. Unified secondary cache 1024kB 2-way, linesize 128 bytes. Synthesized TLB refill handler (37 instructions). Synthesized TLB load handler fastpath (49 instructions). Synthesized TLB store handler fastpath (49 instructions). Synthesized TLB modify handler fastpath (48 instructions). PID hash table entries: 4096 (order: 12, 131072 bytes) Calibrating system timer... 97500 [195.0000 MHz CPU] Using 97.500 MHz high precision timer. Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 308480k/327676k available (3755k kernel code, 18612k reserved, 1081k data, 208k init, 0k highmem) Mount-cache hash table entries: 256 Checking for 'wait' instruction... unavailable. Checking for the multiply/shift bug... no. Checking for the daddi bug... no. Checking for the daddiu bug... no. checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 288k freed NET: Registered protocol family 16 SCSI subsystem initialized EFS: 1.0a - http://aeschi.ch.eu.org/efs/ JFS: nTxBlock = 2416, nTxLock = 19334 SGI XFS with ACLs, large block/inode numbers, no debug enabled rtc: IRQ 8 is not free. DS1286 Real Time Clock Driver v1.0 i8042.c: i8042 controller selftest failed. (0xaa != 0x55) Serial: IP22 Zilog driver (1 chips). ttyS0 at MMIO 0x200000001fbd9830 (irq = 45) is a IP22-Zilog Console: ttyS0 (IP22-Zilog) ttyS1 at MMIO 0x200000001fbd9838 (irq = 45) is a IP22-Zilog io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 1 RAM disks of 9216K size 1024 blocksize loop: loaded (max 8 devices) sgiseeq.c: David S. Miller (dm@engr.sgi.com) eth0: SGI Seeq8003 08:00:69:0a:6d:33 wd33c93-0: chip=WD33c93B/13 no_sync=0xff no_dma=0 debug_flags=0x00 setup_args=,,,,,,,,, Version 1.26 - 22/Feb/2003, Compiled Jun 7 2005 at 21:14:15 wd33c93-1: chip=WD33c93B/13 no_sync=0xff no_dma=0 debug_flags=0x00 setup_args=,,,,,,,,, Version 1.26 - 22/Feb/2003, Compiled Jun 7 2005 at 21:14:15 scsi0 : SGI WD93 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: SEAGATE Model: ST19171W Rev: 2219 Type: Direct-Access ANSI SCSI revision: 02 scsi1 : SGI WD93 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 sending SDTR 0103013f0csync_xfer=2c<5> Vendor: TOSHIBA Model: XM-4101TASUNSLCD Rev: 1084 Type: CD-ROM ANSI SCSI revision: 02 st: Version 20050312, fixed bufsize 32768, s/g segs 256 SCSI device sda: 17783112 512-byte hdwr sectors (9105 MB) SCSI device sda: drive cache: write back SCSI device sda: 17783112 512-byte hdwr sectors (9105 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda9 sda11 Attached scsi disk sda at scsi0, channel 0, id 1, lun 0 sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.20 sr1: scsi-1 drive sr2: scsi-1 drive sr3: scsi-1 drive sr4: scsi-1 drive sr5: scsi-1 drive sr6: scsi-1 drive Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0 Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5 Attached scsi generic sg2 at scsi1, channel 0, id 1, lun 0, type 5 Attached scsi generic sg3 at scsi1, channel 0, id 2, lun 0, type 5 Attached scsi generic sg4 at scsi1, channel 0, id 3, lun 0, type 5 Attached scsi generic sg5 at scsi1, channel 0, id 4, lun 0, type 5 Attached scsi generic sg6 at scsi1, channel 0, id 5, lun 0, type 5 Attached scsi generic sg7 at scsi1, channel 0, id 6, lun 0, type 5 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid10 personality registered as nr 9 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 224.000 MB/sec 8regs_prefetch: 176.000 MB/sec 32regs : 224.000 MB/sec 32regs_prefetch: 172.000 MB/sec raid5: using function: 32regs (224.000 MB/sec) raid6: int64x1 42 MB/s raid6: int64x2 82 MB/s raid6: int64x4 117 MB/s raid6: int64x8 105 MB/s raid6: using algorithm int64x4 (117 MB/s) md: raid6 personality registered as nr 8 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP established hash table entries: 32768 (order: 6, 262144 bytes) TCP bind hash table entries: 32768 (order: 6, 262144 bytes) TCP: Hash tables configured (established 32768 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 208k freed init started: BusyBox v1.00 (2005.06.02-01:26+0000) multi-call binary Starting pid 22, console /dev/ttyS0: '/linuxrc' mount: block device /dev/loop0 is write-protected, mounting read-only Gentoo Linux; http://www.gentoo.org/ Copyright 2001-2005 Gentoo Foundation; Distributed under the GPL Gentoo/MIPS LiveCD RC4 for SGI Indigo2 Impact Systems Built on Prickle-Prickle, the 13rd day of Confusion in the YOLD 3171. * To configure networking, do the following: * For Static IP: * /bin/net-setup [telnet] * For Dynamic IP: * /bin/net-setup dhcp [telnet] * If you would like a telnetd daemon loaded as well, pass "telnet" * As the final argument to /bin/net-setup. BusyBox v1.00 (2005.05.30-06:21+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. / #